Before using your multi-zone inverter mini-split system, please readthis manual carefully and keep it for future reference along with your receipt.Bef
2. Four-way cassette type1. Decide the correct carry-in path.2. Move this unit as originally packaged as possible.3. If the air conditioner is install
10INSTALLATION INSTRUCTIONSThe length could be calculated from Fig.17:Length = 8.3 inches + L (in general, L is half of the whole length of the ins
11INSTALLATION INSTRUCTIONS(2) Install the panel(3) Hang the air-in grid to the panel, then connect the lead terminator of the swing motor and
12INSTALLATION INSTRUCTIONS3. Drainage pipe installation(1) Installation principle(2) Drainage pipe selectionCapacity(x1000Btu)122.4184246307368421
13INSTALLATION INSTRUCTIONSThe horizontal pipe layout should avoid converse flow or bad flow:Drainage pipeWater flowDrainage pipeDrainage pipeDrain
14INSTALLATION INSTRUCTIONSFor the concentrated drainage pipe system, there should design a blowhole at the highestpoint of main pipe to ensure the
15Settlement of outdoor unitAnchor the outdoor unit with a bolt and nut 0.4 inches or 0.3 inches tightlyand horizontally on a concrete or rigid mo
Fit the seal into the drain joint, then insert the drain joint into the base pan hole of outdoor unit, rotate 90 to securely assemble them. Connecti
17CautionAlign the center of the pipes.Sufficiently tighten the flare nut with fingers, and then tighten it with a spanner and torque wrench as sho
18ELECTRICAL WORKFig.61Connect the cable to the outdoor unit1. Remove the electrical control board cover from the outdoor unit by loosening the
1CONTENTSSAFETY PRECAUTIONSWarning ...
One-two models:One-three models:One-four models:Fig.63S(A)L(A)N(A)L(C)N(C)S(C)L(B)N(B) S(B)L(A)N(A)S(A)L(B)L(C)L(D)N(B)N(D)N(C)S(C)S(D)S(B)NOTE:please
ELECTRICAL WORK20Prepare the wiring as follows:1) Never fail to have an individual power circuit specifically for the air conditioner. As forthe meth
Air and moisture in the refrigerant system have undesirable effects as indicated below: Pressure in the system rises. Operating current rises. Cooling
22 AIR PURGINGWhen Using the Vacuum Pump(For method of using a manifold valve, refer to its operation manual.)1. Completely tighten the flare nuts,
A: Lo packed valve B: Hi packed valve C and D are ends of indoor unit connection.CAUTION Gas leak check1. Soapy water method: Apply a soapy wa
2SAFETY PRECAUTIONS Read the following SAFETY PRECAUTIONS carefully before installation. Electrical work must be installed by a licensed el
3Selecting installation placeRead completely, then follow step by step.Indoor unitDo not expose the indoor unit to heat or steam.Select a place where
4Parts List INSTALLATION INSTRUCTIONSLevel gaugeScrewdriverElectric drill, Hole core drill (2.5 inches (65mm))Flaring tool setSpecified torque wrench
This illustration is for explanation purposes only. The actual shape of your air condtioner may be slightly different. Copper lines must be insulated
6 INSTALLATION INSTRUCTIONSFig.4Correct orientation of Installation PlateWallIndoorOutdoor5-7mmFig.6Fig.5Indoor unit installation (wall-mounted type)
7INSTALLATION INSTRUCTIONS1. For the left-hand and right-hand piping, remove the pipe cover from the side panel. 2. For the rear-right-
8INSTALLATION INSTRUCTIONSFig.121. Pass the piping through the hole in the wall.2. Put the upper claw at the back of the indoor unit on th
Kommentare zu diesen Handbüchern